GP2Y0D810Z0F GP2Y0D810Z0F distance measuring sensor unit digital output (100 mm) type applications 1. touch-less switch (sanitary equipment, control of illumination, etc.) 2. robot cleaner features 1. digital output type 2. short distance type detecting distance : typ. 100 mm 3. low profile package size : 13.677.95 mm 4. consumption current : typ. 5 ma 5. battery drive compatible supply voltage : 2.7 to 6.2 v 6. sunlight tolerance 7. add vin terminal, and an external transistor of vcc line is unnecessary at intermittent operating. agency approvals/compliance 1. compliant with rohs directive (2002/95/ec) notice the content of data sheet is subject to change without prior notice. in the absence of confirmation by device specification sheets, sharp takes no responsibility for any defects that may occur in equipment using any sharp devices shown in catalogs, data books, etc. contact sharp in order to obtain the latest device specification she ets before using any sharp device. sheet no.: e4-a01101en date dec.01.2006 ?sharp corporation description GP2Y0D810Z0F is distance measuring sensor unit, composed of an integrated combination of psd (position sensitive detector) , ired (infrared emitting diode) and signal processing circuit. the variety of the reflectivity of the object, the environmental temperature and the operating duration are not influenced easily to the distance detection because of adopting the triangulation method. the output voltage of this sensor stays high in case an object exists in the specified distance range. so this sensor can also be used as proximity sensor. 1
GP2Y0D810Z0F block diagram outline dimensions (unit : mm) product mass : approx. 0.7g signal processing circuit distance measuring ic led drive circuit output circuit oscillation circuit voltage regulator cathode led_fb led gnd reg v cc v cc ? ? v o ? anode c 1 c 2 r 1 ? v in r 1 (led current adjustment resistance = 4.3 ) (led pulse current typ. 70 ma) c 1 c 2 =0.1 f stamp (example) 14 (terminal root) (terminal root) light emitter light detector s 8 1 0 u 4 0 0 1 a b c 13 12 11 10 9 8 7 6 5 4 3 2 1 6.5 7.95 4.7 3 p1.5-5 0.2 0.40 2.5 13.6 7 6.2 (3) (3) year 2006 u mark 2007 v 2008 w 2009 x 2025 t 2026 u .... .... din standard year production (remove g, i, o, q, y, z) (it repeats itself by a period for 20 years) d s u 4 0 0 1 8 1 0 sharp ? s ? GP2Y0D810Z0F month(1 to 9? o, n, d) (din standard symbol) year(din standard symbol) lot no. material case lens device coating lead pin pc (color:black) pc(visible light cut type) pps(color:black) 42alloy(pd-au plating) a b c d symbol cathode led_fb led gnd ?D ?D reg D D D ? v cc ? v in ? v o ? anode (note1) unspecified tolerances shall be 0.3mm. (note2) ( ) : reference value ` : no contact sheet no.: e4-a01101en 2
GP2Y0D810Z0F (t a =25 ,v cc =5v) absolute maximum ratings electro-optical characteristics symbol rating unit supply voltage v cc -0.3 to +7 v output terminal voltage v o -0.3 to v cc +0.3 v input terminal voltage v in -0.3 to v cc +0.3 v operating temperature t opr -10 to +60 storage temperature t stg -20 to +70 * soldering temperature t sol 260 parameter parameter symbol conditions rating unit supply voltage v cc 2.7 to 6.2 v high level input voltage v inh cmos level signal. operating min v cc -0.2 v low level input voltage v inl cmos level signal. standby state max 0.2 v sheet no.: e4-a01101en parameter symbol rating min. typ. max. unit average supply current i cc1 v cc =5v, v in =5v, r 1 =4.3 (*1) D 56.5ma average supply current i cc2 v cc =5v, v in =5v, r 1 =4.3 (*1) D 910.5ma stand-by supply current i cc3 v cc =5v, v in =0v D 58 a v oh output voltage at high level v cc -0.6 DD v v ol output voltage at low level DD 0.6 v detecting distance l (*2)(*3) 80 100 130 mm output voltage (*1) i cc1 : (led emitting time : typ. 20 s 8 times), i cc2 : (emitting time : typ. 20 s 15 times), led pulse current : typ. 70 ma (*2) using reflective object : white paper (made by kodak co., ltd. gray cards r-27white face, reflectance ; 90%) (*3) output voltage switch has a hysteresis width. the distance specified by l should be the distance which the output turns from l to h in case an object moves to the sensor. recommended operating conditions 3
fig. 1 timing chart GP2Y0D810Z0F max 1.88 ms (typ 1.28 ms) v in (input) max 5.65 ms (typ 3.84 ms) (max 3.77 ms) (typ 2.56 ms) nth output second output first output unstable output nth measurement second measurement first measurement v o (output) stand-by stand-by distance measuring operating v cc (power supply) sheet no.: e4-a01101en 4
GP2Y0D810Z0F fig. 2 example of distance measuring characteristics (output) 0 20 40 60 80 100 120 140 160 180 200 distance to reflective object l [mm] output [v] h l hysteresis width set-up detection distance l = 100 mm (typ) l h l h sheet no.: e4-a01101en 5
GP2Y0D810Z0F sheet no.: e4-a01101en notes (incorrect) (correct) (incorrect) (correct) (moving direction) (moving direction) advice for the optics ? the lens of this device needs to be kept clean. there are cases that dust, water or oil and so on deteriorate the characteristics of this device. please consider in actual application. ? please don?t do washing. washing may deteriorate the characteristics of optical system and so on. please confirm resistance to chemicals under the actual usage since this product has not been designed against washing. advice for the characteristics ? in case that an optical filter is set in front of the emitter and detector portion, the optical filter which has the most efficient transmittance at the emitting wavelength range of led for this product ( = 870 70nm), shall be recommended to use. both faces of the filter should be mirror polishing. also, as there are cases that the characteristics may not be satisfied according to the distance between the protection cover and this product or the thickness of the protection cover, please use this product after confirming the operation sufficiently in actual application. ? in case that there is an object near to emitter side of the sensor between sensor and a detecting object, please use this device after confirming sufficiently that the characteristics of this sensor do not change by the object. ? when the detector is exposed to the direct light from the sun, tungsten lamp and so on, there are cases that it can not measure the distance exactly. please consider the design that the detector is not exposed to the direct light from such light source. ? distance to a mirror reflector can not be sometimes measured exactly. in case of changing the mounting angle of this product, it may measure the distance exactly. ? in case that reflective object has boundary line which material or color etc. are excessively different, in order to decrease deviation of measuring distance, it shall be recommended to set the sensor that the direction of boundary line and the line between emitter center and detector center are in parallel. ? in order to decrease deviation of measuring distance by moving direction of the reflective object, it shall be recommended to set the sensor that the moving direction of the object and the line between emitter center and detector center are vertical. notes on handling ? there are some possibilities that the internal components in the sensor may be exposed to the excessive mechanical stress. please be careful not to cause any excessive pressure on the sensor package and also on the pcb while assembling this product. ? soldering shall be done with a soldering iron and below 260 , less than 5s and maximum 2 times. also, please pay attention not to put outer force on lead terminals while soldering. please do not apply flow soldering because it may damage optical lens of the device. 6
GP2Y0D810Z0F sheet no.: e4-a01101en presence of odc etc. this product shall not contain the following materials. and they are not used in the production process for this product. regulation substances : cfcs, halon, carbon tetrachloride, 1.1.1-trichloroethane (methylchloroform) specific brominated flame retardants such as the pbb and pbde are not used in this product at all. this product shall not contain the following materials banned in the rohs directive (2002/95/ec). ? lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (pbb), polybrominated diphenyl ethers (pbde). 7
GP2Y0D810Z0F package specification sheet no.: e4-a01101en product sleeve put products of 40 pieces in sleeve. 8
GP2Y0D810Z0F important notices the circuit application examples in this publication are provided to explain representative applications of sharp devices and are not intended to guarantee any circuit design or license any intellectual property rights. sharp takes no responsibility for any problems related to any intellectual property right of a third party re sulting from the use of sharp's devices. contact sharp in order to obtain the latest device specifi- cation sheets before using any sharp device. sharp reserves the right to make changes in the specifications, characteristics, data, materials, str ucture, and other contents described herein at any time wit hout notice in order to improve design or re liability. manufacturing locations are also subject to change without notice. observe the following points when using any devices in this publication. sharp takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following condi- tions: (i) the devices in this publication are designed for use in general electronic equipment designs such as: --- personal computers --- office automation equipment --- telecommunication equipment [terminal] --- test and measurement equipment --- industrial control --- audio visual equipment --- consumer electronics (ii) measures such as fail-safe function and redundant design should be taken to ensure reliability and safety w hen sharp devices are used for or in connection with equipment that requires higher reliability such as: --- transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) --- traffic signals --- gas leakage sensor breakers --- alarm equipment --- various safety devices, etc. (iii) sharp devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: --- space applications --- telecommunication equipment [trunk lines] --- nuclear power control equipment --- medical and other life support equipment (e.g., scuba). if the sharp devices listed in this publication fall within the scope of strategic products described in the foreign exchange and foreign trade law of japan, it is necessary to obtain approval to export such sharp de vices. this publication is the proprietary product of sharp and is copyrighted, with all rights reserved. under the copy- right laws, no part of this publication may be repro- duced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of sharp. express written permission is also required before any use of this publication may be made by a third party. contact and consult with a sharp representative if there are any questions about the contents of this pu blication. sheet no.: e4-a01101en 9
|
